m30 concrete with ggbs mix design

Concrete Mix Design for M30 grade Civil4M

2017-12-24  Concrete mix Design for M30 Grade concrete with GGBS is as follows; OPC Cement 53 Grade – 280 Kg GGBS – 100 Kg Water Cement ratio (w/c) – 0.4 Free Water – 152 liters 20mm Metal / Aggregates – 772 Kg 10mm Metal / Aggregates – 343 Kg Crush Sand – 918 Kg Admixture Dosage – 1.2 % Admixture – 4.56 Kg Density of Concrete – 2570 Kg/cum

More

SELF-COMPACTING CONCRETE MIX DESIGN FOR M-30

2017-7-24  Further in the trail mix-1 cementation material is taken as 3270kg/ m3 of cement,148.5kg/ m (55%) of fly ash, 108kg/ m3 (40%) of GGBS 32.7kg/ m (1% addition) of silica fumes are used. The W/C material is 0.38 The fine aggregate/total aggregate is 62% The contents of cement, fly ash, GGBS, silica, fine and coarse aggregate, water,

More

Experimental Study On Hybrid Fibre Concrete With Using ...

2021-8-10  concrete ductility and energy absorption, fibre reinforced concrete has been introduced. The present investigation revealed the effect of using GGBS and M Sand as a partial replacement of cement and fine aggregate along with optimum percentage of polypropylene and steel fiber. For this study (M30) grade concrete is designed. Partial

More

Mix design of M30 grade Concrete with admixture as per

2020-3-27  Mix design of M30 grade concrete Projects requirements . 1 Mix design of : M30 grade concrete 2 Type of cement used PPC cement ( supplied only with strength of 33 grade as per clause no 7.4.1 page no 2 of IS 1489 ). conforming to IS 1489 Part 1. -2015.3. Maximum nominal size of aggregate: 20 mm.4. Exposure condition : Moderate exposure condition 5 Workability : mm 50 mm (slump)

More

Concrete Mix Design: Illustrative Example M30 Grade (M20 ...

2021-11-15  Concrete Mix Design Calculation : M20, M25, M30, M40 Grade Concrete Construction Materials / By happhoadmin7 Concrete mix design is a procedure of selecting the suitable ingredients of concrete and their relative proportions with an

More

Sustainable Studies on Concrete with GGBS As a

Table 2. Mix proportions of concrete with various proportions of GGBS replacing cement in M35 grade concrete Mix propotions Controlled concrete 20% GGBS 30% GGBS 40% GGBS W/C ratio 0.41 GGBS content % - 20 30 40 GGBS content (wt) - 0.8 kg 1.2 kg 1.6 kg Cement content 4 kg 3.2 kg 2.8 kg 2.8 kg Sand content 5.186 kg

More

Compressive strength of M30 grade for density 1800 Kg /

The mix design for geopolymer concrete was followed as per BIS codal provisions for ordinary Portland concrete but with some modifications [41]. The ratio of Binder content to Sand was kept as 1:3.

More

Design of self-compacting concrete with ground

2013-1-1  A review of the earlier mix design methods in SCC show that there is no specific method for obtaining SCC based on the strength requirements like conventional vibrated concrete. In this paper a mix proportioning method was proposed for the design of SCC using GGBS based on the strength requirements and considering the efficiency of GGBS.

More

What is maximum content of GGBS in concrete mix design ...

2019-9-14  During this process GGBS is added into it as per % and grinded with clinker and gypsum. After grinding it is stored in silo and then sent for delivery through bag packs or in bulker as loose cement. % denotes the percentage of total quantity of cement.

More

(PDF) Strength and Durability Studies on GGBS Concrete

Split Tensile Strength of concrete for M40 vs % of GGBS From Figure 6 and 7, it is observed that at about 40% replacement of cement with GGBS, concrete attains its maximum split tensile strength ...

More

Mix Design Methodology for Fly Ash and GGBS-Based ...

2020-5-14  Mallikarjuna Rao G., Venu M. (2020) Mix Design Methodology for Fly Ash and GGBS-Based Geopolymer Concrete. In: Subramaniam K., Khan M. (eds) Advances in Structural Engineering. Lecture Notes in Civil Engineering, vol 74.

More

Mix design M30 Grade designed as per IS 10262:2009 IS ...

Mix design M30 Grade designed as per IS 10262:2009 IS 456:2000 (FOR BANGAlORE REGION) DESIGNED By: G.PRABHAKARAN M.TECh, QA/QC ENGINEER. Mix proportioning for a concrete of M30 grade is given in AI to A-ll. AI STIPULATIONS FOR PROPORTIONING. a) Grade designation : M30 b) Type of cement : OPC 53 Grade conforming IS 12269

More

Sustainable Studies on Concrete with GGBS As a

Table 2. Mix proportions of concrete with various proportions of GGBS replacing cement in M35 grade concrete Mix propotions Controlled concrete 20% GGBS 30% GGBS 40% GGBS W/C ratio 0.41 GGBS content % - 20 30 40 GGBS content (wt) - 0.8 kg 1.2 kg 1.6 kg Cement content 4 kg 3.2 kg 2.8 kg 2.8 kg Sand content 5.186 kg

More

Design of self-compacting concrete with ground

2013-1-1  A review of the earlier mix design methods in SCC show that there is no specific method for obtaining SCC based on the strength requirements like conventional vibrated concrete. In this paper a mix proportioning method was proposed for the design of SCC using GGBS based on the strength requirements and considering the efficiency of GGBS.

More

SELF-COMPACTING CONCRETE MIX DESIGN FOR M-30

2017-7-24  Further in the trail mix-1 cementation material is taken as 3270kg/ m3 of cement,148.5kg/ m (55%) of fly ash, 108kg/ m3 (40%) of GGBS 32.7kg/ m (1% addition) of silica fumes are used. The W/C material is 0.38 The fine aggregate/total aggregate is 62% The contents of cement, fly ash, GGBS, silica, fine and coarse aggregate, water,

More

Procedure for Concrete Mix Design of M30 Concrete – Civil ...

Recommended mix proportion of ingredients for grade of concrete M30 obtain from test result – From obtained test result for target strength 38.25 N/mm 2 (> 34 N/mm 2 ,

More

Experimental Study On Hybrid Fibre Concrete With Using ...

2021-8-10  concrete ductility and energy absorption, fibre reinforced concrete has been introduced. The present investigation revealed the effect of using GGBS and M Sand as a partial replacement of cement and fine aggregate along with optimum percentage of polypropylene and steel fiber. For this study (M30) grade concrete is designed. Partial

More

Mix design M30 Grade designed as per IS 10262:2009 IS ...

Mix design M30 Grade designed as per IS 10262:2009 IS 456:2000 (FOR BANGAlORE REGION) DESIGNED By: G.PRABHAKARAN M.TECh, QA/QC ENGINEER. Mix proportioning for a concrete of M30 grade is given in AI to A-ll. AI STIPULATIONS FOR PROPORTIONING. a) Grade designation : M30 b) Type of cement : OPC 53 Grade conforming IS 12269

More

Mix design development of fly ash and ground granulated ...

2018-11-1  The paper presents a rational mix design methodology to produce fly ash and ground granulated blast furnace slag (GGBS) based geopolymer concrete under ambient temperature curing condition. Efforts are made to develop the mix design by integrating ACI strength versus water to cement ratio curve of normal concrete, absolute volume method and ...

More

(PDF) SELF-COMPACTING CONCRETE MIX DESIGN FOR M

Further in the trail mix-1 cementation material is taken as The mix proportion then becomes 270kg/ m3 of cement,148.5kg/ m3 The obtained contents of cement, sand, aggregate and (55%) of fly ash, 108kg/ m3 (40%) of GGBS Cement Sand C.A Water 2.7kg/ m3 (1% addition) of silica fumes are used.

More

CEMENT CONCRETE MIX DESIGN - Dronacharya

2015-9-15  CEMENT CONCRETE MIX DESIGN . DEFINITION ... M30, M35 and M40. In this designation the letter M refers to the mix and the number to the specified 28 day cube strength of mix in N/mm2. The mixes of grades M10, M15, M20 and M25 correspond approximately to the mix proportions

More

Mix Design Concrete Calculation - M20, M25, M30, M35 ...

2020-6-17  B. IS 456-2000 has designated concrete mixes into a number of grades as M10, M15, M20, M25, M30, M35, and M40. In this designation, the letter M refers to the mix and the number to the specified 28-day cube strength of mix in N/mm2. C. Design Mixes. In these mixes, the performance of the concrete is specified by the designer but the mix ...

More

Concrete Mix Design Different Grades of Concrete

2017-5-17  Concrete Mix design of M5, M7.5, M10, M15, M20, M25, M30 and higher grades of concrete is calculated as below: The procedure for finding the different grades of concrete mixes are same. The below mentioned method can be applied to any

More

Silica Fume Ground Granulated Blast Furnace Slag as ...

2016-4-23  3.4 Mix Design Table No. 4 Mix Design Grade Of Concrete M30 Cementitious material 245kg/m3 GGBS ( @ 30% replacement of cement) 105 kg/m3 Coarse aggregate : 20mm kg/m3 Coarse aggregate : 12mm 525 kg/m3 Fine aggregate 701 kg/m3 Water 140 kg/m3 Superplasticizer(S unpla st @ 0. 6 %) 2.1 kg/m3 Fiber (Recron 3s Fiber @ 0.2 % of composite) 5.03 kg/m3

More

© 2021 JETIR June 2021, Volume 8, Issue 6 EFFECT OF ...

2021-6-19  of mineral admixture such as GGBS in the mix design of M30 grade of concrete. All the mix design stipulations and test data for material was carried out with respect to IS 10262 and IS 456-2000. Compressive test were carried out using Compression testing machine (CTM) for that cubes of size 150mm X 150mm were casted

More

Procedure for Concrete Mix Design of M30 Concrete – Civil ...

Recommended mix proportion of ingredients for grade of concrete M30 obtain from test result – From obtained test result for target strength 38.25 N/mm 2 (> 34 N/mm 2 ,

More

Sustainable Studies on Concrete with GGBS As a

Table 2. Mix proportions of concrete with various proportions of GGBS replacing cement in M35 grade concrete Mix propotions Controlled concrete 20% GGBS 30% GGBS 40% GGBS W/C ratio 0.41 GGBS content % - 20 30 40 GGBS content (wt) - 0.8 kg 1.2 kg 1.6 kg Cement content 4 kg 3.2 kg 2.8 kg 2.8 kg Sand content 5.186 kg

More

CEMENT CONCRETE MIX DESIGN - Dronacharya

2015-9-15  CEMENT CONCRETE MIX DESIGN . DEFINITION ... M30, M35 and M40. In this designation the letter M refers to the mix and the number to the specified 28 day cube strength of mix in N/mm2. The mixes of grades M10, M15, M20 and M25 correspond approximately to the mix proportions

More

Influence of Microfine GGBS on Concrete of Grade M35

2019-7-1  Development of efficient concrete mix design plays an important vital role in producing eco-economical concrete. This study represents the effect of presence of mineral admixture micro fine GGBS.GGBS partially replaced added in cement concrete for evaluating the workability and strength of concrete along with flexural split tensile strength.

More

Mix Design Concrete Calculation - M20, M25, M30, M35 ...

2020-6-17  B. IS 456-2000 has designated concrete mixes into a number of grades as M10, M15, M20, M25, M30, M35, and M40. In this designation, the letter M refers to the mix and the number to the specified 28-day cube strength of mix in N/mm2. C. Design Mixes. In these mixes, the performance of the concrete is specified by the designer but the mix ...

More

Concrete Mix Design Different Grades of Concrete

2017-5-17  Concrete Mix design of M5, M7.5, M10, M15, M20, M25, M30 and higher grades of concrete is calculated as below: The procedure for finding the different grades of concrete mixes are same. The below mentioned method can be applied to any

More

Properties of high strength concrete with reduced

2021-11-1  A total of 144 concrete specimens were casted, and the details of specimen type is presented in Table 6. Concrete mix was prepared in a pan mixer as shown in Figure (a). Fine and coarse aggregates were first blended, and later cement and GGBS was added and dry mixing continued Figure 1.

More

IS-10262-2009-CONCRETE MIX DESIGN - INDIAN

2014-4-8  under step:3,u have mentioned in the table that the standard deviation for design mix of the grades of concrete from M30 to M55 as 6,whereas the IS-456:2000 has specified the standard deviation 5 only for the above grades of concreteease verify

More

Establishing a Mix Design Procedure for Geopolymer

2016-5-24  3.1.5 Class C Fly Ash Concrete Mix Design from database..... 25 3.1.6 Class F Fly Ash and Ground-granulated Blast-furnace Slag Concrete Mix Design from database..... 26 3.1.7 Ground-granulated Blast-furnace Slag Concrete Mix Design

More

Ground Granulated Blast Furnace Slag (GGBS) - Sagar

Ground Granulated Blast Furnace Slag (GGBS) GGBS is mainly used as a partial replacement of cement in concrete. When added as an admixture to concrete, it acts as a stabilising agent and improves the quality of concrete. In the production of ready-mixed concrete, GGBS replaces a substantial portion of the Portland cement component, generally ...

More

Design of self-compacting concrete with ground

2016-6-28  of the mix design methodology, literature available today do not suggest any specific procedure for obtaining SCCs of a definite strength as in normal concretes. 4. Proposed method for proportioning GGBS in self compacting concrete This paper

More

Copyright © 2020.Company name All rights reserved.SiteMap